model

HVAC Repair Cost (2026): AC, Furnace and Heat Pump Repairs by Part, and When to Replace

What a contractor's cost is in 2026 to repair an air conditioner, heat pump or furnace, part by part: capacitors, contactors, motors, boards, leak searches and refrigerant by the pound, beside four contractors' published menus, the 2026 refrigerant and tax rules, and one 12-year-old AC priced five ways.

Direct answer: In Clamp's catalog, an AC capacitor is $250 and a contactor $310 in job cost before markup, each with a $125 trip charge; both on one visit are $435. A leak search with a 2 lb R-410A recharge adds $504. A furnace igniter is $335 and a control board $675. A new evaporator coil is $2,057, against $6,159 for a new 3 ton AC with its coil. The ballpark price range for a capacitor, contactor, leak search and 2 lb recharge is $1,221 to $1,878.

The assumptions

This model assumes

  • Each repair is one daytime visit with a $125 trip charge
  • The diagnostic fee is credited to the approved repair
  • Job cost before markup: the visit, parts, labor and refrigerant, no tax
  • 3 ton split system on R-410A unless stated
  • Prices from Clamp's catalog on November 19, 2026

The model, step by step

1AC and heat pump repairs, by part

Priced through Clamp's catalog on November 19, 2026. Every Clamp price in this guide is job cost before markup: what the visit, the part and the labor cost you. Each repair total includes a $125 trip charge. Under each row are the prices four contractors publish: Duct Daddy in Kansas City and Absolute Best Air in metro Atlanta (2026 pages, checked November 2026), South County Air in Orange County, California (November 6, 2026) and Pure Comfort in South Elgin, Illinois (updated November 9, 2026). Theirs are flat rates to the customer, with parts and labor in one number. No source gives one national price, so none is shown.

One repair, one visit
RepairClamp job cost
Run capacitorKansas City $200 to $225. Atlanta $215 to $375. Orange County $300 to $400. South Elgin $275 to $348.$250
ContactorKansas City $250. Atlanta $235 to $430. Orange County $300 to $400. South Elgin $330 to $398.$310
Capacitor and contactorOne visit, one trip charge$435
Condenser fan motorKansas City from $450. Atlanta $425 to $805. Orange County $850 to $1,300. South Elgin $735.$550
Defrost boardHeat pump. Atlanta $470 to $805.$450
Reversing valveHeat pump, with 3 lb of R-410A. Atlanta $1,105 to $1,840.$1,141
CompressorWith 6 lb of R-410A. Kansas City from $2,200. Atlanta $2,000 to $3,395. South Elgin $2,935.$2,707
Clear the drainKansas City $175. Atlanta $215 to $375.$290
Drain and float switchAtlanta, float switch alone: $190 to $315.$425
Compare the menus to the ballpark price range, not to job cost. For a capacitor and contactor on one visit the ballpark price range is $566 to $870. All four menus list the contactor on its own line.
2Refrigerant: four lines, not one

A low charge is four jobs: check the charge, find the leak, fix it, and put refrigerant back. Clamp prices each on its own line. A charge check is $125 and the charging labor is $175 a visit. Refrigerant is a material line by the pound: $22 for R-410A, $24 for R-454B and $75 for R-22. Each total below includes the $125 trip charge.

Refrigerant work, one visit
WorkClamp job cost
Check, add 2 lb R-410ACharge check, recharge labor, 2 lb$469
Same with R-454BKansas City $100/lb. South Elgin $245/lb.$473
Same with R-22Kansas City $175/lb. South Elgin $255/lb.$575
Leak search, electronicAtlanta leak search $320 to $545.$410
Leak search, nitrogenSouth Elgin $610.$550
Find, braze, add 3 lbNitrogen search, one accessible braze, recharge. South Elgin braze alone $710. Atlanta minor leak repair $470 to $865.$1,266
New evaporator coilWith 6 lb of R-410A. Atlanta $1,700 to $2,875. Kansas City from $2,300.$2,057

Why published per-pound prices differ

Your costClamp carries R-410A at $22 a pound. A Pennsylvania shop lists it at $27 a pound and says that price "doesn't include labor time for leak search, repair, or charging" (undated page, checked November 2026).

Retail by the poundKansas City charges $80 a pound for R-410A and $100 for R-454B. Atlanta charges $60 to $115 for either, plus a recharge task of $360 to $605. South Elgin charges $165 for R-410A and $245 for R-454B. A flat rate per pound can carry labor, overhead and profit.

Consumer guidesPickHVAC (May 23, 2026) lists R-410A at $4 to $35 a pound, below all three retail per-pound prices above. Angi lists $40 to $75 (undated, checked November 2026), which reaches only the low end of Atlanta's.

The rules on a home system

No federal leak-repair ruleEPA's HFC leak repair rule took effect January 1, 2026 for appliances holding 15 lb or more. Its fact sheet says home air conditioners and heat pumps "are not covered under these requirements." Topping off a leaking home system is legal under federal rules. Check your state.

Who can do itAttaching gauges or adding refrigerant takes EPA Section 608 certification. Only a certified technician, or a company that shows it employs one, can buy refrigerant for a home system. That covers R-410A and R-454B.

R-22Production and import ended January 1, 2020. An old system can still be serviced with recovered and reclaimed R-22.

Orange County bundles a heat pump leak search and recharge at $700 to $1,500. When a menu bundles, ask what is in the bundle before you compare it to separate lines.
3Furnace repairs, by part

The same four menus, for a gas furnace. Each Clamp total includes the $125 trip charge. Cleaning a flame sensor is its own line below replacing one, and it is worth pricing that way: Kansas City and Atlanta both do.

One furnace repair, one visit
RepairClamp job cost
Clean the flame sensorKansas City $150. Atlanta $130 to $230.$210
New flame sensorKansas City $200. Atlanta $190 to $315. South Elgin $245 to $275.$260
Hot surface igniterKansas City $250. Atlanta $190 to $375. Orange County $350 to $450. South Elgin $245 to $305.$335
Limit or rollout switchAtlanta $190 to $375. South Elgin $325 to $340.$350
Pressure switchAtlanta $300 to $520. Orange County $400 to $600. South Elgin $250 to $355.$360
Blower motor, PSCStandard motor. Kansas City from $775. Atlanta $510 to $920.$645
Inducer motorKansas City $600 to $1,450. Atlanta $640 to $1,150. Orange County $600 to $1,200. South Elgin $400 to $1,095.$650
Gas valveKansas City from $700. Atlanta $385 to $690. South Elgin $505 to $1,120.$650
Control boardKansas City from $500. Atlanta $425 to $805. Orange County $450 to $900. South Elgin $475 to $1,200.$675
Blower motor, ECMVariable speed. Atlanta $1,190 to $2,070. Orange County, any blower: $900 to $1,400.$1,075
A cracked heat exchanger is not on the list. The Orange County contractor publishes no price for it and calls it "usually not worth repairing." Price that call as a furnace replacement.
4The service call: trip, diagnostic and after hours

Every menu above charges to show up and find the fault, and every one drops that fee when the customer approves the repair. Say which way yours works before you quote.

How the fee works

In ClampEach repair carries a $125 trip charge line. The diagnostic is $150. When it is credited to an approved repair it prices at $0. A visit with no repair is $275: the trip and the diagnostic.

Published fees$75 in South Elgin, $79 in Orange County, $89 in Atlanta and $100 in Kansas City, each waived with the repair. ServiceTitan (April 2025) puts the typical fee at $75 to $150.

Not always creditedOne Oklahoma contractor says of its weekend and after-hours call: "the service call is $309, and that is not credited" (May 22, 2026, updated October 29, 2026).

After hoursKansas City charges $200 for a night or Sunday diagnostic, double its daytime fee. South Elgin charges $99 on evenings, weekends and holidays. Trane says emergency rates can run double to triple the regular hourly rate.

The Clamp prices in this guide are for a daytime visit. Add your own after-hours premium.
5The 2026 rules that change the decision

Checked on November 19, 2026. The refrigerant deadline was lifted and the tax credit ended in the last year, and each one moves the repair or replace line.

What applies now

R-410A installsEPA removed the January 1, 2026 installation deadline for R-410A split systems made or imported before 2025. The rule was published May 26, 2026 and took effect July 27, 2026. Old stock can be installed until it runs out. New York keeps a January 1, 2026 date in its own state regulation (6 NYCRR Part 494), so check your state.

R-410A repairsRepairing an existing system was never restricted. Parts are still made, and most distributors in a 2026 trade survey had R-410A at or above their target stock. The next production cut is in 2029. EPA's 2026 rule also keeps R-410A condensing units available as replacement components: "a homeowner can choose to replace their failed condensing unit rather than purchase a whole new system."

The coilA new outdoor unit on R-454B or R-32 needs a new indoor coil or air handler made for it. North Carolina's Office of State Fire Marshal said in a June 2025 code interpretation: "The existing A1 air handler or indoor evaporator coil is required to be replaced." A1 is R-410A's safety class. New coils also carry a refrigerant detection system.

Tax creditThe federal energy efficient home improvement credit (Section 25C) does not apply to anything placed in service after December 31, 2025. A 2026 replacement gets no federal tax credit.

AC and heat pump minimumsA split AC under 45,000 Btu/h is 13.4 SEER2 in the North, by date of manufacture, and 14.3 SEER2 in the Southeast and Southwest, by date of installation. A split heat pump is 14.3 SEER2 and 7.5 HSPF2 everywhere.

Furnace minimum80% AFUE today. A 95% rule applies to furnaces made on and after December 18, 2028 and is not in force. Gas trade groups have asked DOE to move the date to 2030, and in June 2026 the Supreme Court vacated the decision that upheld the rule and sent it back to the appeals court.

Angi's R-410A cost page still gives the January 1, 2026 installation deadline, and its repair or replace page still mentions a federal tax credit (both undated, checked November 2026). Check what your state has adopted before you quote a rule to a customer.
6Repair or replace: the $5,000 rule, age and warranty

The rule: multiply the system's age by the repair price. Over $5,000, replace. No source we found names who wrote it. CBS News (June 24, 2026) calls it "a starting point" and names no author. At 12 years it caps a repair at $417, which a capacitor and contactor already pass.

System age 12 yr
Capacitor, contactor $435
12 x $435 $5,220
The rule's limit $5,000
Over the limit, on a wear part

What decides it

AgeTrane says to repair a unit under 10 years old with minor problems and to consider replacement as it nears 15. CBS says many central systems last 15 to 20 years.

WarrantyCarrier gives 10 years on parts when the system was registered within 90 days and 5 years when it was not. Trane notes that labor and the refrigerant recharge are generally not covered even when the part is.

The capacitorA capacitor and a contactor are wear parts. At $435 they restore cooling, and that repair is sound on a 12-year-old system whatever the rule says.

The coil leakThis is the decision. Topping off is legal and buys time, but the leak stays. A new coil is $2,057 into an old outdoor unit. And a leaking R-410A coil cannot stay under a new R-454B or R-32 condenser, so a replacement includes the coil either way.

The rule uses the customer's price, and the $435 here is job cost before markup, so the real product is higher still. Use the rule to start the conversation, not to end it.
7The worked example: a 12-year-old 3 ton AC

A 12-year-old 3 ton R-410A air conditioner over a gas furnace stopped cooling. The capacitor and the contactor have failed, and the charge is about 2 lb low from a slow leak at the indoor coil. Path A replaces the two parts: $435. Path B adds an electronic leak search and a 2 lb recharge: $939. Path C replaces the two parts and the coil and charges 6 lb: $2,367. Against those, our replacement guide prices a new 3 ton AC with its coil at $6,159, and our heat pump guide prices a heat pump that keeps the furnace as backup (dual fuel) at $7,684.

Path B, repair and recharge: ballpark price range
$1,221 to $1,878
Job cost before markup: path A $435, path B $939, path C $2,367
Trip charge $125
Contactor $185
Capacitor $125
Leak search $285
Recharge labor $175
R-410A, 2 lb $44
$939 job cost before markup
Five ways to answer the same call, job cost before markup
PathJob cost
A. Capacitor, contactorCooling today, the leak stays. Ballpark price range $566 to $870.$435
B. Plus search and 2 lbElectronic leak search, recharge, 2 lb. Ballpark price range $1,221 to $1,878.$939
C. Plus a new coilCapacitor, contactor, coil, 6 lb. Ballpark price range $3,077 to $4,734.$2,367
New 3 ton AC and coilFrom our replacement guide. Add a $225 permit allowance.$6,159
Heat pump, furnace staysDual fuel, from our heat pump guide.$7,684
Clamp's Generate from description screen with the AC repair typed in: capacitor, contactor, leak search and a 2 lb recharge

The call

The AC repair estimate in Clamp at $939 job cost, by trade: the leak search, contactor, recharge labor and capacitor under HVAC, and the trip charge

Every line priced

Path B in Clamp, and the estimate it prices: $939 at job cost. Recreations of the Clamp app with demo data.

Summed from the Atlanta menu's ranges, the same three paths are $450 to $805, $1,250 to $2,185 and $2,150 to $3,680 to the customer, the last before refrigerant. Do the capacitor and contactor today on any path. Then show the customer the coil, the new AC and the heat pump side by side.
8What to offer at the repair

Only the upgrades with a sourced price are here. The federal credit that used to help sell the bigger ones ended with 2025.

Four worth a line on the quote

Hard-start kit$225 in Clamp when it rides on a repair visit, $350 as its own call. Kansas City lists $250 and Atlanta $275 to $490.

Dual fuelA heat pump in place of the AC, with the furnace kept as backup: $7,684 in our heat pump guide. Fixr (January 2025) put the conversion at $2,500 to $8,000, before the new refrigerants and their matched coils.

ZoningHomeGuide's national average is $3,100. In an existing home it lists $1,700 to $2,800 for two zones and $350 to $500 for each zone after (undated, checked November 2026). PickHVAC (May 27, 2026) puts most jobs at $1,200 to $5,500. It is not priced from Clamp's catalog in this guide.

Smart thermostatPickHVAC lists thermostat upgrades at $75 to $350 each, and HomeGuide a smart thermostat at $100 to $250. Neither is a dated installed price for one thermostat, so quote your own.

We found no usable installed prices for UV lights, media filter cabinets, surge protectors or duct sealing, so they are left out.

What it means

What to doPrice the trip, each part, the leak search, the recharge and the refrigerant as separate lines. Replace the wear parts today. When the indoor coil is leaking on an old system, put the coil, a new AC and a heat pump in front of the customer side by side.
The example, path B: $1,221 to $1,878 ballpark price range on $939 job cost before markup.

Every repair, line by line

Describe the fault and the parts. Clamp prices the trip, each part, the leak search, the recharge and the refrigerant by the pound on their own lines.

The capacitor gets the system running. The coil decides what happens next.

Questions

How much does AC repair cost?

It depends on the part. In Clamp's catalog a capacitor is $250, a contactor $310, a condenser fan motor $550 and a compressor $2,707 in job cost before markup, each with a $125 trip charge. Four contractor menus from Kansas City, metro Atlanta, Orange County and South Elgin, Illinois list a capacitor at $200 to $400 to the customer, and three of them a compressor from $2,000.

How much does it cost to replace an AC capacitor?

Clamp's catalog prices a run capacitor at $250 in job cost before markup: a $125 trip charge and $125 for the part, installed. The ballpark price range is $325 to $500. Published contractor menus list $200 to $225 in Kansas City, $215 to $375 in metro Atlanta, $275 to $348 in South Elgin, Illinois and $300 to $400 in Orange County, California.

How much does a refrigerant recharge cost?

A charge check and a 2 lb R-410A recharge is $469 in job cost before markup in Clamp's catalog: the trip, the check, $175 of charging labor and refrigerant at $22 a pound. Finding the leak is a separate line, $285 for an electronic search. Contractors' retail prices per pound run $80 in Kansas City, $60 to $115 in metro Atlanta and $165 in South Elgin, Illinois.

How much does furnace repair cost?

In Clamp's catalog, cleaning a flame sensor is $210, an igniter $335, a pressure switch $360, an inducer motor $650, a control board $675 and a variable-speed blower motor $1,075 in job cost before markup, each with a $125 trip charge. Published contractor menus list an igniter at $190 to $450 and a control board at $425 to $1,200, depending on the region.

Should I repair or replace my AC?

Replace a failed capacitor or contactor on any system; they are wear parts. The real decision is a refrigerant leak at the indoor coil on an older system. In Clamp's catalog a new coil is $2,057 and a new 3 ton AC with its coil is $6,159 in job cost before markup. A new R-454B or R-32 outdoor unit needs a new matched coil, and there is no federal tax credit for a 2026 replacement. The "$5,000 rule" (age times repair price) is a rule of thumb with no known author.

Related

Sources & provenance

  1. Clamp's catalog, priced by script Clamp (research)
  2. Furnace, AC and boiler replacement cost Clamp (research)
  3. Heat pump and mini split installation cost Clamp (research)
  4. Heating and cooling repair prices Duct Daddy (Kansas City) (research)
  5. Repair pricing Absolute Best Air (McDonough, Georgia) (research)
  6. Furnace repair cost in Orange County South County Air Services (Orange County, California) (research)
  7. AC Repair in South Elgin, IL Pure Comfort (South Elgin, Illinois) (research)
  8. Furnace Repair in South Elgin, IL Pure Comfort (South Elgin, Illinois) (research)
  9. HVAC Service/Repair Reider Plumbing & Heating (Elizabethtown, Pennsylvania) (research)
  10. R-454B and R-32 refrigerant service in Oklahoma Hartzell's Heat & Air (Kingfisher, Oklahoma) (research)
  11. What is a Diagnostic Fee? A Guide for HVAC Businesses and Their Customers ServiceTitan (research)
  12. What Is the Average Central Air Conditioner Repair Cost? Trane (research)
  13. AC Refrigerant and Freon Cost Per Pound (R22/R410A/R32/R454B) 2026 PickHVAC (research)
  14. How Much Does R-410A Refrigerant Cost per Pound? [2026 Data] Angi (research)
  15. American Innovation and Manufacturing Act: Leak Repair Requirements for Appliances Containing Hydrofluorocarbons and Certain Substitutes US Environmental Protection Agency (official source)
  16. Section 608 technician certification requirements US Environmental Protection Agency (official source)
  17. Refrigerant sales restriction US Environmental Protection Agency (official source)
  18. Residential air conditioning and the phaseout of HCFC-22: what you need to know US Environmental Protection Agency (official source)
  19. Phasedown of Hydrofluorocarbons: Reconsideration of Certain Regulatory Requirements Promulgated Under the Technology Transitions Provisions of the American Innovation and Manufacturing Act of 2020 US Environmental Protection Agency (official source)
  20. EPA Finalizes Refrigerant Rule Update to Allow Older HVAC Unit Installation National Association of Home Builders (research)
  21. Part 494 fact sheet New York State Department of Environmental Conservation (official source)
  22. There's plenty of R-410A to be found, for now ACHR News (research)
  23. Compatible/Properly Matched Partial Replacement of a Split System Heat Pump or Air Conditioner: A2L Refrigerant Considerations (interpretation 03041) North Carolina Office of State Fire Marshal (official source)
  24. What Does Evaporator Coil Replacement Cost? Trane (research)
  25. FAQs for modification of sections 25C, 25D, 25E, 30C, 30D, 45L, 45W and 179D under Public Law 119-21 IRS (official source)
  26. 2023 central air conditioner standards: frequently asked questions US Department of Energy (official source)
  27. 10 CFR 430.32, Energy and water conservation standards and their compliance dates eCFR (official source)
  28. Energy Conservation Standards for Consumer Furnaces, final rule US Department of Energy (official source)
  29. Energy Conservation Program: Notification of Petition for Rulemaking US Department of Energy (official source)
  30. 95% furnace efficiency rule to get new hearing ACHR News (research)
  31. What is the $5,000 rule for HVAC systems? CBS News (research)
  32. Air Conditioning Replacement: Should I Repair or Replace My AC Unit? Angi (research)
  33. Air Conditioning Replacement or Repair: What's Right for You? Trane (research)
  34. Carrier Warranty Registration and Information Carrier (research)
  35. Dual Fuel Heat Pump Cost / Hybrid Heat Pump Cost Fixr (research)
  36. How much does an HVAC zoning system cost to install? HomeGuide (research)
  37. HVAC Zoning System Cost 2026 PickHVAC (research)
Changes: Nov 19, 2026: Published: AC, heat pump and furnace repairs by part, refrigerant jobs, and repair or replace, priced from Clamp's catalog.